Finally Dynoed My I-Speed RS Conversion
#1
VIP Member
Thread Starter
iTrader: (3)
Join Date: Jan 2003
Location: Petaluma, NORCAL
Posts: 767
Car Info: 98 2.5RS WR Blue (breathin fire/not on fire)
Finally Dynoed My I-Speed RS Conversion
1998 RS Power Mods
I-speedusa EJ20 Conversion (stock internals)
I-speedusa Ecutek
APS Topmount Intercooler (large)
IHI VF35 Turbo
GFB Stealth BOV
STI Injectors
STI Engine & Tranny Mounts
STI Radiator Cap
ACT Clutch
Exedy Flywheel
HKS Uppipe
Custom 3" Turboback Exhaust
Magnaflow High Flow Cat & Muffler
PWR Radiator
K&N Box Filter
Samco Intercooler Hoses
Samco Radiator Hoses
Tuned @ 91 Octane (76 Gas)
Special thanks to Adam...Chris...& Bill @ I-SpeedUSA
I-speedusa EJ20 Conversion (stock internals)
I-speedusa Ecutek
APS Topmount Intercooler (large)
IHI VF35 Turbo
GFB Stealth BOV
STI Injectors
STI Engine & Tranny Mounts
STI Radiator Cap
ACT Clutch
Exedy Flywheel
HKS Uppipe
Custom 3" Turboback Exhaust
Magnaflow High Flow Cat & Muffler
PWR Radiator
K&N Box Filter
Samco Intercooler Hoses
Samco Radiator Hoses
Tuned @ 91 Octane (76 Gas)
Special thanks to Adam...Chris...& Bill @ I-SpeedUSA
Last edited by RS TURBO; 06-06-2003 at 10:48 AM.
#10
VIP Member
Thread Starter
iTrader: (3)
Join Date: Jan 2003
Location: Petaluma, NORCAL
Posts: 767
Car Info: 98 2.5RS WR Blue (breathin fire/not on fire)
pretty much what wrexr said....i hopin for low 12's...after my most recent tune and addition of that APS top mount, i noticed huge midrange and top end improvements....fourth gear pulls hard too redline...and i mean hard!!!! By the dyno plot you can tell it's carryin high boost all the way to redline....Next wednesday i'll be at Infineon attemptin to blow another tranny!!!
#12
Registered User
iTrader: (1)
Join Date: Jan 2003
Location: Maryland
Posts: 59
Car Info: 2000 Subaru Impreza 2.5 RS
That is one sweet looking RS. How much did the motor swap, labor and motor cost you. I have a 2000 RS and am thinking about dropping an ej20 into it. You should get clear side markers for your car too.
#14
@Stoptech
iTrader: (5)
Join Date: Nov 2002
Location: San Francisco, CA
Posts: 2,416
Car Info: 2002 WRX Wagon
wow a VF35 huh? i thought those were smaller than the 34s. does it still have the ball bearing center section? i just haven't hear much about that turbo. also, what boost are you running?
haha i was reading your list, saw the STi radiator cap and was like there goes another crappy stock radiator, but then I saw that PWR and was like SWEET!! (yeah, i know i sound like a goddam valley girl, "like totally like sweet!!!" )
you've got a nice smooth torque curve too, congradulations!! your car looks great (for an RS!! hahaha jk) and hauls some serious ****!!
haha i was reading your list, saw the STi radiator cap and was like there goes another crappy stock radiator, but then I saw that PWR and was like SWEET!! (yeah, i know i sound like a goddam valley girl, "like totally like sweet!!!" )
you've got a nice smooth torque curve too, congradulations!! your car looks great (for an RS!! hahaha jk) and hauls some serious ****!!
#15
VIP Member
Thread Starter
iTrader: (3)
Join Date: Jan 2003
Location: Petaluma, NORCAL
Posts: 767
Car Info: 98 2.5RS WR Blue (breathin fire/not on fire)
thanks for the love!!!! The VF35 isn't ball bearing yet it is one of the newest IHI turbos using a divided thrust bearing!!!! it has the same compressor as the VF30 (i think) but has a smaller exhaust side for faster spool up...basically no turbo lag!!!!