Does anyone have some heat shield insulation for wiring?
12-25-2003, 01:11 AM
#1
VIP Member
Thread Starter
iTrader: (3)
Join Date: Nov 2002
Location: Lastweek Lane - Watertown, NY
Posts: 10,133
Car Info: 02WRXpseudoSTiWannabeWagon
Does anyone have some heat shield insulation for wiring?
Also, Mario. I almost forgot about that short shifter. Do you still want it?
12-25-2003, 11:47 AM
#4
VIP Member
Thread Starter
iTrader: (3)
Join Date: Nov 2002
Location: Lastweek Lane - Watertown, NY
Posts: 10,133
Car Info: 02WRXpseudoSTiWannabeWagon
Mike, wilco. I'll give you a little time to wake up though.
Dean, Probably not more than 15'. Maybe 20. The wire is about 1/4" dia.
Dean, Probably not more than 15'. Maybe 20. The wire is about 1/4" dia.
12-25-2003, 02:34 PM
#5
Registered User
iTrader: (7)
Join Date: Dec 2002
Location: Flying on the H1 w/ 75 psi of compression on all 4 cyl
Posts: 2,859
Car Info: PnP VF30 w/ STi injectors Perrin intake walbro fuel pump w/ a TXS TBE
Oh yeah thanks for reminding me, Yes i would still like it. I'm poor until payday. Can you hold it for me until then please?
12-25-2003, 02:58 PM
#7
Registered User
iTrader: (14)
Join Date: Jan 2003
Location: Honolulu, HI
Posts: 1,224
Car Info: 1991 Toyota MR-2 Turbo
Originally posted by gpatmac
Dean, Probably not more than 15'. Maybe 20. The wire is about 1/4" dia.
Dean, Probably not more than 15'. Maybe 20. The wire is about 1/4" dia.
I don't have that much but I got lots of the exhaust wrap if you wanna try it. LMK.
12-25-2003, 08:01 PM
#10
VIP Member
Thread Starter
iTrader: (3)
Join Date: Nov 2002
Location: Lastweek Lane - Watertown, NY
Posts: 10,133
Car Info: 02WRXpseudoSTiWannabeWagon
Even added a little bit of the heat wrap stuff to the inside of the heat shield.
BTW, the TUNA is almost done. Does anyone have the faintest clue what temps you should see about 15" down the downpipe, away from the turbo?
We tried to see if we could measure at that bung and compare with what the EGT gauge said, where the EGT sensor is at the #3 on the manifold. I can't have the WB sensor where the temp is higher than 1382 degrees F.
I know I could put the WB sensor at the same place where the stock NB is, but I think that that would be a pain in the ***.
BTW, the TUNA is almost done. Does anyone have the faintest clue what temps you should see about 15" down the downpipe, away from the turbo?
We tried to see if we could measure at that bung and compare with what the EGT gauge said, where the EGT sensor is at the #3 on the manifold. I can't have the WB sensor where the temp is higher than 1382 degrees F.
I know I could put the WB sensor at the same place where the stock NB is, but I think that that would be a pain in the ***.
Thread
Thread Starter
Forum
Replies
Last Post
gtfaded
Engine/Power - EJ20T (pre-2006 WRX and JDM)
12
03-23-2007 07:08 AM